Saniflo SaniACCESS 3 Upflush Toilet Kit

  • $1,322.92
    Unit price per 
  • Save $233.08

Availability: In stock- ships same day
Shipping: FREE SHIPPING 2-5 Days UPS
Tax: No Sales Tax save up to 10% 

SaniACCESS 3 Upflush Kit Includes

  1. SaniACCESS 3 macerating bathroom pump
  2. White toilet bowl (standard or elongated)
  3. White toilet tank
  4. FREE soft-close Toilet Seat!
  5. Extension for behind wall installation (optional)

SaniACCESS 3 Benefits

The SaniACCESS 3 is a system that is used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniACCESS 3 pump is designed to connect with:

  1. This SaniACCESS 3 Upflush Toilet
  2. Any Sink
  3. Any Shower
  4. Any Bath

SaniACCESS 3 Installation

The SaniACCESS 3 is simplicity itself to install; there are just four connections.

  1. The macerating/pump is connected to the spigot of a horizontal outlet toilet. 
  2. The toilet tank is connected to the water supply. 
  3. The macerating/pump is connected to the small diameter discharge pipe work. 
  4. The macerating/pump is connected to the electrical supply. 
Then optionally connect the discharge pipes from the sink, shower and/or bath.

SaniACCESS 3 vs. SaniPLUS Comparison

The SaniACCESS 3 and the SaniPLUS are virtually the same pump, except the SaniACCESS 3 was recently redesigned with a modular layout for easier access to the electrical components and the macerating blades. So in the rare case of a clog, you can quickly clear it yourself with no need for a plumber.

SaniACCESS 3 Function

The inside of the unit comprises of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump.

When the flush is activated, the water flowing into the SaniACCESS 3 activates a micro switch in the pressure chamber, which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A common spindle/shaft drives the impeller and the macerator blades.  The moving parts therefore are kept to an absolute minimum.  Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.  The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.  The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall).  Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again.  A normal operating cycle for SaniACCESS 3 takes about 10 - 15 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. 

In addition to the toilet waste, the SaniACCESS 3 will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal.  When adding a bathtub or shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit. 

The wastewater from other sanitary fixtures is discharged into the SaniACCESS 3 via two 2-inch inlets on either side of the housing.  Either one or both inlets can be used as required.  The discharge elbow on top of the unit can be turned either to the left, to the right, or towards the back, depending on the discharge installation.  A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. 

This unit has been designed with a vent connection on the top of the unit.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.  It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

Periodic maintenance can be accomplished easily without having to disconnect the unit from either the toilet or the rest of the plumbing system.  Through one service panel, a service contractor can access the electrical components as well as the level sensor mechanism of the pump.  The second service panel provides ready access to the basket area around the macerating blades for easy removal of any large objects that may have been accidentally flushed.

The SaniACCESS3 has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. 

SaniACCESS 3 Water Conservation

The water closet the SaniACCESS 3 is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush.

SaniACCESS 3 Warranty

2-Year Full Manufacturer Warranty
Extended 3-Year Warranty with Product Registration (

How SaniACCESS 3 Works: Instructional Video


SaniACCESS 3 Product Specifications


UPC#s 082, 003 and 005

UPC# 030 (Extension Pipe) 


H10 3/4" x W18 3/4" x D6 3/4"

H27cm x W47.5cm x D17cm 


Induction Motor

No carbon brushes or gears.

Tested over 30,000 cycles. 3600 rpm. 


110-115V; 60Hz; 15 Amps 

Usage 4.65 Amps


Horizontally to 150 ft (50m)

Gravity Fall on Horizontal installations: 1/4" per ft 

Pumps vertically to 15 ft (4m) 





Polypropylene, C.R.P., Stainless Steel, Neoprene






15–20 secs

subject to installation pipe run 


1.28 US gal

4.8 liters


7.35 gal/m

27 l/m 


More step-by-step installation guides and spec sheets available to our customers.
Just email us with your order number and we'll be happy to help!



BOWL Round Front Elongated Front
TANK Vitreous china tank Vitreous china tank
HEIGHT (SEAT) 16-3/4 inches 16-3/4 inches
DEPTH (OVERALL)      26-1/2 inches 28-1/2 inches
VOLUME 1.28 gpf 1.28 gpf
WARRANTY 1 year on china 1 year on china


       INSTALLATION - Visible         INSTALLATION - Behind Wall