Looking for a durable macerating upflush toilet that also features an alarm and automated start/stop? Look no further than the Saniflo Sanipack. In stock and ready to ship the same day you purchase it, this unit is ideal for a full bathroom addition. Capable of pumping vertically up to 9 feet, the Sanipack connects to wall-hung toilets, sinks, and showers. Designed for installation inside a wall cavity, the Sanipack can install a full bathroom up to 9 feet below a sewer line, and up to 100 feet from a soil stack.
Want to install the Sanipack on your own? No problem at all - the unit only features four connections. These include a connection from the macerator/pump to the discharge pipe, a connection from the toilet tank to the water supply, a connection from the macerator/pump to the small diameter discharge pipe, and a connection from the macerator to the electrical supply.
Ready to learn more about the Sanipack? Contact our team for more information today.
Availability: In stock- ships same day
Shipping: FREE SHIPPING 2-5 Days UPS
Tax: No Sales Tax save up to 10%
Type: Macerating Upflush Toilet
Product #: 011
Ideal Use: Full Bathroom Addition
Features and Benefits:
Pumps vertically up to 9 ft
Connects a wall hung toilet, sink and shower
SaniPACK macerating pump
SaniALARM: warns if water level in macerator is unusually high
Descaler: cleaner, removes hard water deposits in macerator
The SaniPACK is a macerator device which is meant to be installed inside a wall cavity. The SaniPACK is a system that is used to install a complete bathroom up to 9 feet below the sewer line, or even up to 100 feet away from a soil stack. It can handle the effluent from a toilet, sink and shower.
The SaniPACK is simplicity itself to install; there are just four connections.
The macerator/pump is connected to the discharge pipe coming from a wall hung toilet
The toilet tank is connected to the water supply
The macerator/pump is connected to the small diameter discharge pipe work
The macerator/pump is connected to the electrical supply
The Saniflo SaniPACK Macerating Upflush Toilet is not location-specific and is suitable when setting up temporary toilets. This toilet can be part of the toilet, shower or sink and can be moved to different locations by simply unscrewing the connections.
This system requires only connection to the discharge pipe, water supply, wall-hung toilet and electric supply making it easy to install, anywhere. The Saniflo saniPACK does not tamper with the floor of the bathroom, and the discharge elbow rotates in all directions to fit different plumbing needs. CleanThe case of the Saniflo SaniPACK Macerating Upflush Toilet hides the macerating pump, pipes and reservoir from view, giving the bathroom a neat appearance. Everything is designed to fit within the wall cavity.
The inside of the SaniPACK is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump.
When the flush is activated, the water flowing into the SaniPACK activates a micro switch in the pressure chamber which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the macerator blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM. The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.
The unit pumps the effluent upward to 9 feet and/or 100 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again. A normal operating cycle for SaniPACK takes about 7-9 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal.
In addition to the toilet waste, the SaniPACK will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a shower and a urinal. When adding a shower, a base will have to be constructed. This base should be made out of a 2" x 6" (minimum) or 2" x 8" (recommended) on edge, to allow for the installation of a P-trap and the required 1/4"per foot gravity flow towards the pump unit.
The waste water from other sanitary fixtures is discharged into the SaniPACK via two 1-1/2 inch inlets on either side of the housing. Either one or both inlets can be used as required. The discharge elbow on top of the SaniPACK can be turned either to the left, to the right, or towards the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.
This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.
It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.
The SaniPACK is designed to be used with a wall hung toilet. The depth of the case allows for this pump to be installed within the wall. Since the reservoir, the macerating pump and the pipes are hidden from view, this type of installation gives you the lean and clean look of a European bathroom.
Plumbing Code Certified:
The SaniPACK has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9.