SaniBEST Pro: Heavy-Duty Macerating Pump

  • $1,125.02
    Unit price per 
  • Save $198.98


Availability: In stock- ships same day
Shipping: FREE SHIPPING 2-5 Days UPS
Tax: No Sales Tax save up to 10% 

SaniBEST Pro Benefits

The SaniBEST Pro is a system that is used to install a complete bathroom and/or laundry room up to 25 feet below the sewer line, or even up to 150 feet away from a soil stack. The SaniBEST Pro pump is designed to connect with:

  1. A SaniBEST Pro Upflush Toilet
  2. Any Sink
  3. Any Shower
  4. Any Bath
  5. Any Washing Machine

While most of Saniflo pump ranges are macerators, the SaniBEST Pro incorporates an actual grinder system.  The SaniBEST Pro is ideal for situations where you do not control the use of it (ie. rental unit, offices, warehouses, etc).  The SaniBEST Pro is designed to deal with sanitary articles that may have been flushed down the toilet; such articles may consist of sanitary napkins, q-tips, dental floss, etc.

SaniBEST Pro Installation

The SaniBEST Pro is simplicity itself to install; there are just four connections.

  1. The macerating/pump is connected to the spigot of a horizontal outlet toilet. 
  2. The toilet tank is connected to the water supply. 
  3. The macerating/pump is connected to the small diameter discharge pipe work. 
  4. The macerating/pump is connected to the electrical supply. 
Then optionally connect the discharge pipes from the sink, shower, bath and/or washing machine.

SaniBEST Pro Function

The inside of the SaniBEST Pro is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel cutting blade and the pump.  When the flush is activated, the water flowing into the SaniBEST Pro activates a micro switch in the pressure chamber, which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A common spindle/shaft drives the impeller and the blades.  The moving parts therefore are kept to an absolute minimum.  Water and organic waste matter, enter the chamber and are reduced to slurry as the blades rotate at 3600 RPM.  The reduced solids are picked up at the bottom and the impeller mounted beneath the motor ejects the waste.

The unit pumps the effluent upward to 25 feet and/or 150 feet horizontally (with gravity fall).  Once the water level in the container goes down, the micro switch deactivates.  A normal operating cycle for the SaniBEST Pro takes about 7-9 seconds depending upon the discharge pipe run configuration.

In addition, the SaniBEST Pro will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bath/shower, a urinal and even a washing machine (indirect connection).  When adding a bathtub/shower, a base will have to be constructed.  This base should be made out of a 2” x 6” (minimum) or 2”x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit.

The wastewater from other sanitary fixtures is discharged into the SaniBEST Pro via two 1½-inch inlets on either side of the housing.  The discharge elbow on top of the SaniBEST Pro can be rotated 360 degrees depending on the discharge installation.  A non-return valve (included in assembly) prevents back flow into the unit.

This unit has been designed with a vent connection on the lid.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.

The SaniBEST Pro unit must be connected to our rear discharge toilet.  It is highly recommended for the grinder to be connected to a Ground Fault Interrupter (GFI) circuit.

The SanibBEST Pro has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9.  

SaniBEST Pro Water Conservation

The water closet the SaniBEST Pro is connected to, uses much less water than a regular toilet, it uses 6 liters (1.6 US Gal) of water per flush.

SaniBEST Warranty

2-Year Full Manufacturer Warranty
Extended 3-Year Warranty with Product Registration (www.Saniflo.com/Register)

How SaniFlo Works: Instructional Video

 

SaniBEST Pro Product Specifications

PART NUMBERS

UPC#s 013, 003 and 005

UPC# 030 (Extension Pipe)

DIMENSIONS (PUMP ONLY)

H10.5" x W20 5/16" x D8"

H26.8cm x W52cm x D20.5cm 

MOTOR

Induction Motor

No carbon brushes or gears.

Tested over 30,000 cycles. 3600 rpm. 

ELECTRICAL SUPPLY

110-115V; 60Hz; 15 Amps 

Usage 9 Amps

DISCHARGE

Horizontally to 150 ft (50m)

Gravity Fall on Horizontal installations: 1/4" per ft 

Pumps vertically to 25 ft (7.6m) 

DISCHARGE PIPE DIAMETER

3/4"

21mm 

CONSTRUCTION MATERIALS

Polypropylene, C.R.P., Stainless Steel, Neoprene

 

MAX TEMPERATURE

104°F

40°C 

NORMAL RUNNING TIME

7–9 secs

subject to installation pipe run 

WATER PER FLUSH

1.28 US gal

4.8 liters

VOLUME

7.35 gal/m

27 l/m 

Downloads

More step-by-step installation guides and spec sheets available to our customers.
Just email us with your order number and we'll be happy to help!

Important Note (Includes PUMP ONLY)

This product is the the SaniBEST Pro pump only. It is for customers who want to replace an old pump and already have the SaniFlo toilet bowl that attaches to the SaniBEST Pro. If you do not have a bowl already, you need to purchase the complete SaniBEST Pro upflush macerating toilet system here.